Bus Bar Clip

Written By: Dozuki System (and one other contributor)
  • Comments: 6
  • Favorites: 0

Difficulty

Moderate

Steps

36

Time Required

Suggest a time??

Sections

1

Flags

0

Introduction

Overview

This guide demonstrates how to replace a bus bar clip in an Open Vault system. == Acronyms and Terms == * HDD - Hard Disk Drive * Mini-SAS - Mini Serial Attached SCSI * SCSI - Small Computer System Interface === Additional Notes === It is not absolutely necessary to remove trays from the Open Vault chassis to replace the Powerblade cable. This section of the replacement guide may be treated as a preference.

  1. The server can be powered off remotely or on the hardware itself.

    • The server can be powered off remotely or on the hardware itself.

    • Remote Power Down: Login to the server to power it off.

    • shutdown -h now;exit

    • Hardware Power Down: Press and hold the power switch for at least three seconds, as annotated.

    Edit

  2. Pull the Mini-SAS cable from the nylon cable management clip. Pull the Mini-SAS cable from the nylon cable management clip.

    • Pull the Mini-SAS cable from the nylon cable management clip.

    Edit

  3. Disconnect the Mini-SAS cable from the storage tray. Use the pull-tab to disconnect the cable, as shown.

    • Disconnect the Mini-SAS cable from the storage tray.

    • Use the pull-tab to disconnect the cable, as shown.

    Edit

  4. Locate the two tray release levers. These release levers secure the tray to the storage chassis.

    • Locate the two tray release levers.

    • These release levers secure the tray to the storage chassis.

    • Press both tray release levers upwards.

    • Pushing the tray release handles inwards may assist in actuating the tray release levers.

    • Pull the two release handles that snap outward.

    • Slide the tray forward until fifteen hard disk drives can be seen.

    Edit

  5. Press the two Powerblade cable retention tabs. Pull the cable towards the rear until it unseats from its connector. Pull the cable towards the rear until it unseats from its connector.

    • Press the two Powerblade cable retention tabs.

    • Pull the cable towards the rear until it unseats from its connector.

    Edit

  6. Open fifteen hard disk drive cages. Press the green retention tab on the hard disk drive cage. Rotate the cage to access the hard disk drive.

    • Open fifteen hard disk drive cages.

    • Press the green retention tab on the hard disk drive cage.

    • Rotate the cage to access the hard disk drive.

    Edit

  7. Push each hard disk drive away from the pivot point of each gate. This will unseat the drives from their SATA and power connectors. Remove each hard disk drive.

    • Push each hard disk drive away from the pivot point of each gate.

    • This will unseat the drives from their SATA and power connectors.

    • Remove each hard disk drive.

    Edit

  8. Place the hard disk drives on a work bench or cart.

    • Place the hard disk drives on a work bench or cart.

    • It may be beneficial to rest the hard disk drives on an static-free mat to minimize risk of damaging the drives.

    • Because the drives will be reinstalled in the tray, it is beneficial to place them in a logical order to hasten their reinstall.

    Edit

  9. Close the hard disk drive cages. Press in the green tab on each drive gate.

    • Close the hard disk drive cages.

    • Press in the green tab on each drive gate.

    • Press the gate downwards. Release the green tab to lock the gate.

    Edit

  10. Locate the black thumbscrew in the middle-rear of the storage tray. Loosen the thumbscrew. Loosen the thumbscrew.

    • Locate the black thumbscrew in the middle-rear of the storage tray.

    • Loosen the thumbscrew.

    Edit

  11. Press down two storage tray locking tabs.

    • Press down two storage tray locking tabs.

    • The storage tray locking tabs are located towards the left-rear and right-rear of the tray.

    • Pull the tray away from the Open Rack.

    • If depressing the tray locking tabs do not release the tray, push the tray into the chassis about 10cm. Extend the tray again until its about 5cm from its full extension. Press the locking tabs downwards and pull the tray.

    Edit

  12. Place the tray upside down on a work bench so that the tray circuit boards are exposed, as shown.

    • Place the tray upside down on a work bench so that the tray circuit boards are exposed, as shown.

    Edit

    • Remove the remaining storage tray.

    • The process to remove the second tray is identical to removing the first tray.

    Edit

  14. Remove the six chassis fans. Unscrew the thumbscrew on each of the fans.

    • Remove the six chassis fans.

    • Unscrew the thumbscrew on each of the fans.

    • Grasp the fan handle and slide it to the rear. Lift the fan upwards.

    Edit

  15. Push the storage chassis about 5cm from the rear of the rack.

    • Push the storage chassis about 5cm from the rear of the rack.

    • Be careful whenever working around the Open Rack bus bars. Never touch live bus bars.

    Edit

  16. Go to the front of the Open Rack. Remove the storage chassis from the Open Rack.

    • Go to the front of the Open Rack.

    • Remove the storage chassis from the Open Rack.

    Edit

  17. Loosen the two thumbscrews on top of the chassis lid. Pull the lid towards the rear of of the chassis. Pull the lid towards the rear of of the chassis.

    • Loosen the two thumbscrews on top of the chassis lid.

    • Pull the lid towards the rear of of the chassis.

    Edit

  18. Unscrew one Phillips #2 screw securing the bus lead management clip to the fan controller board. Unscrew one Phillips #2 screw securing the bus lead management clip to the fan controller board. Unscrew one Phillips #2 screw securing the bus lead management clip to the fan controller board.

    • Unscrew one Phillips #2 screw securing the bus lead management clip to the fan controller board.

    Edit

  19. Unscrew four Phillips #2 screws that secure the bus bar leads to the fan controller board. Unscrew four Phillips #2 screws that secure the bus bar leads to the fan controller board. Unscrew four Phillips #2 screws that secure the bus bar leads to the fan controller board.

    • Unscrew four Phillips #2 screws that secure the bus bar leads to the fan controller board.

    Edit

  20. Unscrew four Torx T10 screws.

    • Unscrew four Torx T10 screws.

    Edit

  21. Remove the bus bar clip from the Open Vault chassis. Remove the bus bar clip from the Open Vault chassis.

    • Remove the bus bar clip from the Open Vault chassis.

    Edit

  22. Insert a new bar clip into the chassis.

    • Insert a new bar clip into the chassis.

    • It is important to ensure that positive and negative lead polarity is oriented as indicated by the markings on the chassis, as annotated. Power polarity is indicated as follows:

    • PWR: (+)

    • GND: (-)

    Edit

  23. Screw in the Phillips #2 screw to secure the bus lead management clip to the fan controller board. Screw in the Phillips #2 screw to secure the bus lead management clip to the fan controller board.

    • Screw in the Phillips #2 screw to secure the bus lead management clip to the fan controller board.

    Edit

  24. Screw in four Phillips #2 screws to secure the bus leads to the fan controller board.

    • Screw in four Phillips #2 screws to secure the bus leads to the fan controller board.

    • It is important to ensure that positive and negative lead polarity is oriented as indicated by the markings on the chassis. Power polarity is indicated as follows:

    • PWR: (+)

    • GND: (-)

    Edit

  25. Install the lid on the storage chassis.

    • Install the lid on the storage chassis.

    • The lid installation process is opposite of its removal process.

    Edit

  26. Slide the chassis into the Open Rack. Slide the chassis into the Open Rack.

    • Slide the chassis into the Open Rack.

    Edit

  27. Install the six chassis fans.

    • Install the six chassis fans.

    • The fan installation process is opposite of its removal process.

    Edit

  28. Slide the storage tray back into the storage chassis.

    • Slide the storage tray back into the storage chassis.

    • Make sure no cables are obstructing the path of the tray when sliding the tray into the chassis.

    Edit

  29. Tighten the storage tray thumbscrew. Route the Powerblade cable behind the storage tray tab.

    • Tighten the storage tray thumbscrew.

    • Route the Powerblade cable behind the storage tray tab.

    • This tab is located just left of the thumbscrew.

    Edit

  30. Route the Powerblade cable behind the tray cable guide, as annotated.

    • Route the Powerblade cable behind the tray cable guide, as annotated.

    • Connect the Powerblade cable to the storage tray.

    • Rear chassis LEDs will illuminate blue upon a proper connection.

    Edit

  31. Install the hard disk drives that were previously removed.

    • Install the hard disk drives that were previously removed.

    Edit

  32. Close and secure the hard disk drive cages. Close and secure the hard disk drive cages. Close and secure the hard disk drive cages.

    • Close and secure the hard disk drive cages.

    Edit

  33. Slide the tray back into the rack.

    • Slide the tray back into the rack.

    • Secure the tray by locking the both pull handles.

    • Push the handles towards the storage tray.

    • A distinctive 'click' will be heard when the handles have properly locked.

    Edit

  34. Connect the Mini-SAS cable to the storage tray.

    • Connect the Mini-SAS cable to the storage tray.

    Edit

  35. Route the Mini-SAS cable in the nylon cable management clip.

    • Route the Mini-SAS cable in the nylon cable management clip.

    Edit

  36. Press the power button.

    • Press the power button.

    Edit
Conclusion

This work is licensed under a Creative Commons Attribution 4.0 International License.

Author

with 1 other contributor

Dozuki System

Member since: 09/24/2009

1 Reputation

142 Guides authored

6 Comments

Classification, Design and accessories of Cable Tray:

Cable tray can be fabricated and design according to industrial usage and plant specifications; it could be in following types.

Ladder Cable tray:

A stair type ladder tray consists of Rungs which is joint by two sheet walls. It has relevantly less weight.

Perforated Cable tray:

Design, bend and fabricated a one piece of material and perforated by punches. It has high weight as compared to Ladder cable Tray.

Abid - Reply

Cable tray used for electrical cable distribution in the building’s structural plants and pipe racks, cable laying cable routing at cable tray also use for protection. Cable tray used for all control and power cables cable tray also use as mechanical protection of cable protect from falling off any object directly at the live cable, cable trays are manufactured of different types.

Cable ladder

Perforated cable tray

Cable duct

Cable Mesh

Abid - Reply

The types of cables, allowed in cable tray, and the wiring methods permitted in cable trays can be found in NEC Section 392.10 (A). This Section also lists various corresponding NEC Articles which describe the conditions of use and installation requirements for a particular class or type of cable. Additional considerations such as fill capacity, allowable ampacity, cable splicing within trays, and securing and supporting cables are addressed in Article 392. Users should be familiar with all these Articles and check the manufacturer’s specifications, to verify selected cables meet all application requirements and NEC requirements.

Abid - Reply

Cable tray use for cable managements to protect the cables and for proper dressing of cables. Cable tray use at almost all industry sizes and material selection will be different for every project cable tray material selection also depends on the process and indoor-outdoor usage and at cable types

Three major types of cable tray

1-            Perforated cable tray

2-            Ladder Type Cable tray

3-            Wire mesh type cable tray

<a href="https://www.alfazalengineering.com/cable...>Cable Tray</a>

Abid - Reply

Alfazal Engineering providing services for '''''Cable tray''''', Tower tray, and other sheet metal work at very economical prices with the best delivery time all over Pakistan. tower trays for the refinery.

Cable Tray street lighting poles manufacturer in Pakistan by Al-Fazal Engineering

Perforated Cable Tray Made of Sheets With Perforation on the based. Cable Gland, Cable tray distributor in Pakistan. We are available for your support 24/7 and 100% guarantee for quality. We never compromise in quality.

Abid - Reply

Add Comment

View Statistics:

Past 24 Hours: 2

Past 7 Days: 3

Past 30 Days: 12

All Time: 791